Presentations -
-
Developments of a Vibration-free I.C. Piston Engine Based on a “Basement and Radial” Configuration Design (Design Theory for the Compact and non-Combustion Operation of 2nd Prototype Engine)
Haruki USHIMARU, Gen TAKASE, Yojiro ISHINO, Yu SAIKI
2024.12
Event date： 2024.12
Language：Japanese Presentation type：Oral presentation (general)
Country：Japan
A novel engine geometry, which is named provisionally as "basement and radial configuration", was proposed and investigated in this paper. The geometry gives a vibration-free and kinematic energy fluctuation-free property to motions of plural parts; i.e. pistons. A single radial arm rotor drives all the moving pistons in this configuration. In this study, a prototype three-cylinder internal combustion engine based on the geometry was designed and manufactured. The specifications of the prototype engine are as follows: the number of cylinders of 3, a piston displacement of 21cc x 3, a cylinder bore of 30 mm, a piston stroke of 30 mm, a compression ratio of 4.9, propane as fuel, a valve system of a rotary valve. A trial operation of the prototype engine resulted in the achievement of firing operation (8.1W output at 311 rpm) without any support of electrical motor and so on. This paper gives the pressure variations in the three combustion chambers on the firing condition. The theory and design for a compact 2nd prototype engine were reported. Especially the detailed design of the mechanism of crankshaft rotation, which consists of main-crankshaft, sub-crankshafts, split needle bearings, and a radial arm rotor, has also been provided.
-
Development of a 100% Ammonia firing Package Burner of 20kW Class
Yojiro ISHINO, Kenji NISHIZAWA, Yuki MATSUI, Kakeya WATANABE, Yu SAIKI
2024.11
Event date： 2024.11
Language：Japanese Presentation type：Oral presentation (general)
Country：Japan
-
Developments of a Vibration-free I.C. Piston Engine Based on a “Basement and Radial” Configuration Design (Firing Engine Operation of the 1st Prototype Engine and Design Theory for the Compact 2nd Prototype Engine)
Haruki Ushimaru, Momoka Komeda, Gen Takase, Ryosuke Hibi, Yojiro Ishino
2024.05
Event date： 2024.05
Language：Japanese Presentation type：Oral presentation (general)
Country：Japan
A novel engine geometry, which named provisionally as "basement and radial configuration", was proposed and investigated in this paper. The geometry gives a vibration-free and kinematic energy fluctuation-free property to motions of plural parts; i.e. pistons. In this configuration, all the moving pistons are driven by a single radial-arm-rotor. In this study, a prototype three-cylinder internal combustion engine based on the geometry was designed and manufactured. The specifications of the prototype engine are as follows: a number of cylinders of 3, a piston displacement of 21cc x 3, a cylinder bore of 30 mm, a piston stroke of 30 mm, a compression ratio of 4.9, propane as fuel, a valve system of a rotary valve. A trial operation of the prototype engine resulted in achievement of firing operation (8.1W output at 311 rpm) without any support of electrical motor and so on. In this paper the pressure variations in the three combustion chambers on the firing condition was provided. The theory and design for a compact 2nd prototype engine was also reported.
-
Developments of a Vibration-free I.C. Piston Engine Based on a “Basement and Radial” Configuration Design (Firing Engine Operation of the 1st Prototype Engine and Design Theory for the Compact 2nd Prototype Engine)
2024.05
Event date： 2024.05
Language：Japanese Presentation type：Poster presentation
Country：Japan
-
Development of Tele-Existence Thermal Haptics Robot Arm System for Experiencing Remote Interactive Thermal(hot/cold) Environment（Prototype Design of a Haptic Exoskeleton Wearable Arm Device and Reproducibility of Remote Temperature Environment Provided by Wearable Device）
Kaito Kawamura, Kumi Yamane, Takashi Ichikawa, Yojiro Ishino
2023.10
Event date： 2023.10
Language：Japanese Presentation type：Oral presentation (general)
Country：Japan
In this study, the development of the tele-existence robot arm in which human beings can experience not only the haptic environment but also the thermal (hot/cold) environment was focused on. In this report, the temperature transmission system was actually developed, and the trial operations were conducted. A comparison between reproductivities of two types of thermal control units of wearable device to generate a cold environment was made. For the development of a proper wearable device, it is important to design the configuration of joints of the wearable device so as to allow every motions and postures of an operator without any interruption. A prototype design of a wearable arm device, originated from a collar bone joint, with a novel (111) isometric shoulder configuration, was also introduced.
-
新型・無振動内燃ピストンエンジンの実動作の確認（ベース・ラジアル機構を利用した設計）
米田百花，日比瞭介，牛丸春貴，石野洋二郎
自動車技術会2023年秋季大会 第６回学生ポスターセッション 2023.10 自動車技術会
Event date： 2023.10
Language：Japanese
Venue：名古屋 Country：Japan
無振動，一定運動エネルギーの物体運動を与える機構である「ベース・ラジアル機構」を見出した．この機構に基づけば，多様なエンジン・流体機械の設計が可能となるが，本研究では，低振動な内燃エンジンの設計・試作を行いった．発表では，設計理論の説明と，本試作エンジンの燃料による自立運転の結果の報告を行う．
-
Development of Tele-Existence Haptics Robot Arm System for Force and Thermal (hot/cold) Environments(Prototype Design of a Novel Shoulder Configuration Haptic Exoskelton Wearable Arm Device Originated from Collar bone Joint)
Yojiro ISHINO,Tetsuji TSUKADA,Kumi YAMANE,Kaito KAWAMURA
2023.06
Event date： 2023.06 - 2023.07
Country：Japan
Robot systems capable of experiencing remote environments are urgently required for future lack of manpower and aging society. In this study, the development of the tele-existence robot arm system in which human beings can experience not only the haptic environment but also the thermal (hot/cold) environment was focused on. In this system, operator's shoulder and arm should be restricted by an exoskelton wearable device to get motion and posture information of a remote robot arm. For development of a proper wearable device, it is important to design the configuration of joints of the wearable device so as to allow every motions and postures of an operator without any interruption. Especially, a shoulder joint of human is so functional that the reproduction by a simple mechanical structure has been almost difficult. In this report, prototype design of a wearable arm device, originated from collar bone joint, with a novel (111) isometric shoulder configuration, was introduced.
-
Development of Tele-Existence Haptics Robot Arm System for Force and Thermal (hot/cold) Environments (Improvement in Reproducibility of Remote Environments Provided by Wearable Haptic Device)
Kumi YAMANE, Tetsuji TSUKADA, Kaito KAWAMURA, Yojiro ISHINO
2023.06
Event date： 2023.06 - 2023.07
Language：Japanese Presentation type：Poster presentation
Country：Japan
Robot systems capable of experiencing remote environments are urgently required for future lack of manpower and aging society. In this study, the development of the tele-existence robot arm in which human beings can experience not only the haptic environment but also the thermal (hot/cold) environment was focused on. In this report, the temperature transmission system was actually developed, and the trial operations were conducted. In the operations, a remote finger-tip-like temperature measuring unit touching a moderately (50degC)-heated test block (aluminum) transmitted a PWM signal of a temperature variation to an on-site wearable unit. Consequently, the reproduction of the remote temperature sensing data was succeeded by controlled heating based on the transmitted information in the wearable unit. In this paper, first, the reproducibility was indicated by the result of the positive(hot) temperature variation of the temperature measurement unit of the on-site finger probe in the wearable unit. Second, comparison between reproductivities of two types of thermal controll units of wearable device to generate a cold environment was made.
-
Multi-Directional Schlieren 3D-CT(Computer Tomography) measurement of Ammonia-Air Premixed Flames on an Open-type Swirl Burener
2022.11
Event date： 2022.11
Language：Japanese Presentation type：Oral presentation (general)
Country：Japan
-
A Vibration-free I.C. Piston Engine Based on a "Basement and Radial" Configuration Design (Construction of the Prototype Engine and Investigation of the Firing Engine Operation)
2022.11
Event date： 2022.11
Language：Japanese Presentation type：Oral presentation (general)
Country：Japan
-
Development of Tele-Existence Thermal Haptics Robot Arm System for Experiencing Remote Interactive Thermal Environment (Reproducibility of Remote Temperature Environment Provided by Wearable Device)
Kumi Yamane，Tetsuji Tsukada，Yojiro Ishino
2022.10
Event date： 2022.10
Language：Japanese Presentation type：Oral presentation (general)
Country：Japan
-
Microscopic Image Diagnostics with Visible Emission Light for Self-burning Surface Temperature Distribution of CFRP (Carbon Fiber Reinforced Plastic) in Oxygen International conference
Yojiro Ishino，Rion Ito
2022.08 Pacific Center of Thermal Fluids Engineering (PCTFE)＆The Visualization Society of Japan (VSJ)
Event date： 2022.08
Language：English Presentation type：Oral presentation (general)
Country：Japan
Carbon Fiber Reinforced Plastic(CFRP) has been widely used in variety industries because of its high strength-density ratio. Therefore disposal method of waste CFRP should be considered in advance now. We have been proposed a combustion incineration of carbon fiber(CF) residue after recycle use. However, carbon fiber residue is almost impossible to be burned out by even high temperature burnt gas because of extremely high melting point of carbon fiber and a low oxygen concentration in burnt gases[1].
In this study, self-sustained combustion of carbon fiber in oxygen has been reported. In order to obtain information of the self-sustaining mechanism of the combustion, in this paper, a convenient optical technique to acquire the 2D distribution of high surface temperature of glowing solid material was conducted.
In this technique, magnified thermographic view of the high temperature specimen was provided by comparison between RGB brightness information of conventional photograph of the visible light emission of the surface and previously-calculated values from Planck's law and the spectral sensitivity of the camera system.
In this paper, first, accuracy of the method was verified by comparison between the 2D temperature distribution result of a glowing fine (0.5 mm dia.) graphite rod in burnt gas of a propane-air premixed laminar flame and its estimated temperature distribution measured by PR-type thermocouple and compensated by Kaskan's method. Next magnified instantaneous 2D temperature diagnostics of self-burning carbon fiber bundle in oxygen was made. The 2D surface temperature distribution result gives very high temperature over 2900 K on carbon fiber surface in in-oxygen combustion incineration. -
Development of a Vibration-free I.C. Engine Based on a "Basement and Radial" Configuration Design and Investigation on its Properties in Firing Engine Operation
2022.07
Event date： 2022.07
Language：Japanese Presentation type：Oral presentation (general)
Country：Japan
-
Research and Development of a Novel Vibration-free I.C. Piston Engine Based on a "Basement and Radial" Configuration Design
Takuma Oikawa, Momoka Komeda, Yojiro Ishino
Event date： 2022.07
Language：Japanese Presentation type：Oral presentation (general)
Country：Japan
-
Development of Tele-Existence Thermal Haptics Robot Arm System for Acquiring and Experiencing Remote Thermal Environment
Tetsuji Tsukada, Ryo Sugiura, Kumi Yamane, Yojiro Ishino
2022.07
Event date： 2022.07
Language：Japanese Presentation type：Oral presentation (general)
Country：Japan
-
Three-dimensional Measurements of Turbulent Ammonia Flames by Multi-Directional Schlieren CT(Computer Tomography) Technique
Yojiro Ishino, Tomoya Kunishima, Yuki Matsui, Yuki Mori
2022.07
Event date： 2022.07
Language：Japanese Presentation type：Oral presentation (general)
Country：Japan
-
Multi-Directional Schlieren 3D-CT(Computer Tomography) Measurement of Instantaneous Temperature Distributions of Turbulent Flames (Improvement in accuracy with Standard Refractive Index Gas Jets )
Yojiro Ishino, Tomoya Kunishima, Yuki Mori, Xiangdong Cao,Yuki Matsui
Event date： 2021.10
Language：Japanese Presentation type：Oral presentation (general)
Non-scanning 3D-CT(Computer Tomography) technique using a multi-directional quantitative schlieren system with flash light sources has been proposed to obtain instantaneous 3D density distributions of flames, supersonic jets and etc. This "Schlieren 3D-CT" is based on (i) simultaneous acquisition of flash-light schlieren images taken from numerous directions, and (ii) 3D-CT reconstruction of the images by an appropriate CT algorithm. In this paper, accuracy of this technique is evaluated and verified by checking with a standard refractive index distribution of a helium jet. Next, the verified 3D distribution of refractive index of premixed flames are successfully converted to appropriate temperature distribution.
-
Temperature Measurement of Self-burning CFRP(Carbon Fiber Rainforced Plastic) in Oxygen (Image Diagnostics of High Surface Temperature with Visible Light Emission)
Yojiro Ishino, Yumiko Ishihara
Event date： 2021.10
Language：Japanese Presentation type：Oral presentation (general)
Carbon fiber is almost impossible to be burned out by even high temperature burnt gas because of extremely high melting point of carbon fiber and a low oxygen concentration in burnt gases. In previous studies, self-sustained combustion of carbon fiber in oxygen has been reported. In order to obtain information of the self-sustaining mechanism of the combustion, in this paper, a convenient optical technique to acquire the 2D distribution of high surface temperature of glowing solid material was conducted. In this technique, magnified thermographic view of the high temperature specimen was provided by comparison between RGB brightness information of conventional photograph of the visible light emission of the surface and previously-calculated values from Planck's law and the spectral sensitivity of the camera system.
-
THREE-DIMENTIONAL MEASUREMENT ON THERMAL STRUCTURE OF SIX CLUSTERED METHANE-AIR DIFFUSION MICROFLAMES International conference
Yuta Uchida, Harumi Kondo, Zhaojin Diao, Taro Hirasawa, Michael Winter, Yojiro Ishino, Kozo Saito
The Second Pacific Rim Thermal Engineering Conference ASTFE, JSME, KSME
Event date： 2019.12
Language：English Presentation type：Oral presentation (general)
Venue：Maui, Hawaii, USA
-
ウエアラブル＆ロボットアームで遠隔地の温・力触覚環境を体験！
石野洋二郎，鶴谷 敏之，杉浦 良，ENKHTUR Bayarjavkhlan
名工大テクノフェア2019 名古屋工業大学
Event date： 2019.11
Language：Japanese Presentation type：Poster presentation
Venue：名古屋工業大学
-
High-Speed Flash Schlieren 3D-CT(Computer Tomography) Measurement of Instantaneous Density Distributions of High Speed Fluctuating Flows in Supersonic Jets
Yojiro ISHINO, Ahmad Zaid NAZARI, Takanori MOTOHIRO, Ryoya YAMADA, Fumiya ITO, Haruumi KONDO, Yoshiaki MIYAZATO,Sinichiro NAKAO
Event date： 2019.09
Language：Japanese Presentation type：Oral presentation (general)
-
ウエアラブル＆ロボットアームで遠隔地の温・力触覚環境を体験！
石野 洋二郎，鶴谷 敏之，杉浦 良，ENKHTUR Bayarjavkhlan
イノベーション・ジャパン2019 大学見本市 国立研究開発機構 科学技術振興機構
Event date： 2019.08
Language：Japanese Presentation type：Poster presentation
Venue：東京ビッグサイト 青海展示棟B
-
Study on Combustion Incineration of CFRP (SEM Observations of Nano Level Sharpening of Carbon Fiber Residue Tips and Temperature Measurements Based on Heat Radiation Images) International conference
Y. Ishino, M. Tabata, S. Onuma
International Workshop on Environmental Engineering 2019 (IWEE2019) The Japan Society of Mechanical Engineers, Environmental Engineering Division
Event date： 2019.06
Language：English Presentation type：Oral presentation (general)
Venue：Okinawa, Japan
Carbon fiber, contained in CFRP(carbon fiber rainforced plastic), is almost impossible to be burned out by even high temperature burnt gas because of extremely high melting or sublimation point of carbon fiber and a low oxygen concentration in burnt gases. In this study, first, oxygen nozzle of 10 mm x 30 mm exit size, which equipped fuel (propane) pipe of inner diameter of 0.8 mm for a pilot ignition flame, has been introduced to observe the in-oxygen-combustion behaiviors of test pieces of (i) CFRP slender plate (2 mm wide and 1 mm thickness), (ii)slender plate of CFRP-P (Plastic removed CFRP), "G"FCRs("Graphite" Fine Cylindrical Rod) of diameters of 0.38 mm, 0.55 mm and 0.72 mm.
-
Application of Thermal Haptics to Tele-Existence Haptics Robot Arm for Remote Thermal Environments
Toshiyuki TSURUYA, Koki OUCHI, Yojiro ISHINO
Event date： 2019.06
Language：Japanese Presentation type：Poster presentation
Robot systems capable of experiencing remote environments are urgently required for future lack of manpower and aging society. In this study, development of the tele-existence robot arm in which human beings can experience not only the haptic environment but also the thermal environment was targeted. In this report, first, a tele-haptics robot arm system, driven by torque control, was introduced. Silicon rubber is used for the fingers of the robot arm because its thermal conductivity is close to that of human skin. In order to investigate the temperature rise caused by contact with a heating body, thermocouples were embedded at the depths of 0.3, 0.6 and 0.9 mm of the silicone rubber finger tips. Temperature measurement was carried out when a high temperature aluminum cylinder of 60 deg.C was touched with a heavy force of 7.8 N and a light force of 0.86 N. The results was compared with numerical simulated results.
-
CT (COMPUTER TOMOGRAPHY) MEASUREMENT OF 3D DENSITY DISTRIBUTIONS OF FLAME: OBTAINING VERTICAL GRADIENT SCHLIEREN BRIGHTNESS FROM HORIZONTAL GRADIENT FOR IMAGE-NOISE REDUCTION International conference
Ahmad Z. Nazari, Yojiro Ishino, Ryoya Yamada, Takanori Motohiro, Fumiya Ito, Harumi Kondo, Yoshiaki Miyazato, Shinichiro Nakao
4th Thermal and Fluids Engineering Conference (TFEC) American Society of Thermal and Fluids Engineers
Event date： 2019.04
Language：English Presentation type：Oral presentation (general)
Venue：LasVegas, NV, USA
Using a delicate multi-directional quantitative schlieren optical system, the 20-directional observation of high-speed premixed turbulent flame, non-uniform density flow, by employing non-scanning 3D-CT (three-dimensional computer-tomography) technique has been conducted. The 3D density distributions data of target flame by using ML-EM (Maximum Likelihood-Expectation Maximization) an appropriate CT (computer-tomography) algorithm are successfully reconstructed. In the previous report, a novel technique "multi-path integration" is proposed for noise reduction in projections (density thickness) images of CT (computer-tomography). Multi-path integration is required schlieren brightness gradient in both horizontal (x-directional) and vertical (z-directional) directions, or in other words, in two orthogonal directions (e.g. horizontal and vertical or two perpendicular diagonal directions). The 20-directional quantitative schlieren optical system presents only images of schlieren brightness in the horizontal gradient (x-directional) and another 20-directional optical system seems necessary to obtain vertical (z-directional) schlieren brightness gradient, simultaneously. In the present investigation, the report deals with introducing a new technique for obtaining vertical schlieren brightness gradient from horizontal experimental data without the necessity of a new optical system. This new approach is a simple and inexpensive solution. First, for a deep understanding of complex schlieren brightness, a numerical simulation is performed. Next, the initial density thickness (Dt) images are obtained from images of schlieren brightness in the horizontal gradient (x-directional). Finally, using inverse process from density thickness (Dt) images, the vertical (z-directional) and diagonal schlieren brightness gradient data of target flame successfully obtained. The mentioned technique can be used for obtaining any optional directions of schlieren brightness gradient.
-
ウエアラブル＆ロボットアームで遠隔地の温・触覚環境を体験！ Invited
石野 洋二郎，大内 洸輝，鶴谷 敏之
ロボットシンポジウム2019名古屋 ロボットシンポジウム2019名古屋実行委員会
Event date： 2019.02
Language：Japanese Presentation type：Poster presentation
Venue：名古屋市，吹上ホール
-
複数燃料種が混在する予混合気体場の当量比分布の定量シュリーレン瞬間三次元CT計測- 当量比・屈折率の普遍関係式に基づく当量比計測 -
石野洋二郎，近藤晴海，元廣孝徳，Ahmad Zaid NAZARI，山田凌矢，伊東郁哉
第56回燃焼シンポジウム 日本燃焼学会
Event date： 2018.11
Language：Japanese Presentation type：Poster presentation
Venue：堺市産業振興センター
「当量比」は，各種燃料と酸化剤（空気）との混合割合を与える値であり，燃焼にとって，適正混合・燃料過剰・空気過剰などの状態を表現する，極めて重要なパラメーターである．
本研究では，この「当量比」に注目し，「複数種の燃料が混在する予混合気体場の当量比分布」を計測する手法を提案する．さらに，この提案を，「定量シュリーレン三次元CT計測法」[1,，2]に適用し，当該予混合気が存在する流れ場の瞬間三次元当量比分布の計測を試みる． -
CFRP（炭素繊維強化プラスチック）の焼却処理に関する研究- ナノレベル先鋭化燃焼過程と電子顕微鏡観察 -
石野洋二郎，田畑まどか，當山良太
第56回燃焼シンポジウム 日本燃焼学会
Event date： 2018.11
Language：Japanese Presentation type：Poster presentation
Venue：堺市産業振興センター
炭素繊維強化プラスチック（CFRP）の今後の利用量の増大に備え，難燃性CFRPの最終焼却処分方法について検討する必要がある．前報[1]では，CFRP，とくに炭素繊維CFが，3000℃を超える高温燃焼ガスであっても全く燃焼しないこと，しかし，酸素流領域では極めて明瞭に燃焼することが確認され，温度条件よりはむしろ，高濃度酸素条件がCFRPの燃焼・焼却に有効であることを示した．本報では，はじめに前報[1]の結果（CFRP-P（後述）および"G"FCRの酸素燃焼実験）を記載する．本報ではさらに，"G"FCR周囲の燃焼ガス流動の観察，"G"FCR表面の赤熱状況撮影および赤熱画像のRGB分解を行った．
-
成分不明な複数種類の燃料が混在する予混合気体場での当量比分布の新計測法の提案
石野洋二郎，近藤晴海，元廣孝徳
名工大テクノフェア2018 名古屋工業大学
Event date： 2018.11
Language：Japanese Presentation type：Poster presentation
Venue：名古屋工業大学
-
遠隔地の温・触覚環境を体験するサーマルハプティクス（熱触覚技術）ロボットアームの開発と体験展示
石野洋二郎，大内洸輝，鶴谷敏之
名工大テクノフェア2018 名古屋工業大学
Event date： 2018.11
Language：Japanese Presentation type：Poster presentation
Venue：名古屋工業大学
力触覚環境だけでなく，「熱触覚環境」，すなわち，火炎や熱風などによる「流動熱環境」や，高温物体との接触にともなう「接触熱環境(*)」をヒトが体験できるロボットアームの開発を目指して，実機を試作した．
-
CFRP（炭素繊維強化プラスチック）の焼却処理に関する研究（燃焼過程と燃焼物形状）
石野洋二郎，田畑まどか，當山良太
日本機械学会 2018年度年次大会 日本機械学会
Event date： 2018.09
Language：Japanese Presentation type：Oral presentation (general)
Venue：関西大学 千里山キャンパス
炭素繊維強化プラスチック（CFRP）は軽量かつ高強度のため，航空機や自動車などに多用されており，今後の利用量の増大に備え，難燃性CFRPの最終焼却処分方法について検討する必要がある．本研究（１）では，CFRP，とくに炭素繊維CFが，3000℃を超える高温燃焼ガスであっても全く燃焼しないこと，しかし，酸素流領域では極めて明瞭に燃焼・焼却することが確認され，温度条件よりはむしろ，高濃度酸素条件がCFRPの燃焼・焼却に有効であることを示した．本報では，はじめに前報（１）の結果，すなわち，試験片としてプラスチック成分を燃焼除去したCFRP（CFRP-Pと記載）の細板と，構造がより単純なグラファイト細径円柱（"G"FCR : "Graphite" Fine Cylindrical Rod，シャープペンシル替芯（太さ0.3, 0.5, 0.7 mm））とを使用し，酸素燃焼実験を行った結果を記載する．"G"FCRの燃焼特性の理解ならびに解析手法は，CFRPの燃焼解析の際に利用できるので，本報ではさらに，"G"FCR周囲の燃焼ガス流動の観察，"G"FCR表面の赤熱状況撮影および赤熱画像のRGB分解を行った．
-
定量シュリーレン三次元CT計測における進展（当量比の計測と複素シュリーレン法によるノイズリダクション）
山田凌矢，アハマド・ザイード・ナザリ，元廣孝徳，伊東郁哉，近藤晴海，石野洋二郎，宮里義昭，仲尾晋一郎
日本機械学会 2018年度年次大会 日本機械学会
Event date： 2018.09
Language：Japanese Presentation type：Oral presentation (general)
Venue：関西大学 千里山キャンパス
本研究では，密度変化を伴った流体現象に対して多方向からの定量シュリーレン同時撮影を実施し，得られたシュリーレン画像を用いて三次元データを得る計測法(1-2)を提案した．この計測法を「成分不明な複数種類の燃料が混在する予混合気の当量比」の計測に用いて，当該予混合気が存在する流れ場の瞬間三次元当量比分布の計測を試みた．また，CT再構成精度の向上の為，画像解析を行う前にノイズの低減（ノイズリダクション）を目的とした画像処理が必要であると考えられる．そこで，従来のシュリーレン画像を拡張した「複素シュリーレン画像」という概念を導入し，その特性を用いた新しいノイズリダクション技術を提案する．
-
Development of a Thermo-Fluid Haptics Tele-Existence Robot Arm for Remote Thermal Environments
Event date： 2018.07
Language：Japanese Presentation type：Oral presentation (general)
Robot systems capable of experiencing remote environments are urgently required for future lack of manpower and aging society. In this study, development of the tele-existence robot arm in which human beings can experience not only the haptic environment but also the thermal environment was targeted. Silicon rubber is used for the fingers of the robot arm because its thermal conductivity is close to that of human skin. In order to investigate the temperature rise caused by contact with a heating body, thermocouples were embedded at the depths of 0.3, 0.6 and 0.9 mm of the silicone rubber finger tips. Temperature measurement was carried out when a high temperature aluminum cylinder of 60 deg.C was touched with a heavy force of 7.8 N and a light force of 0.86 N. The results was compared with numerical simulated results.
-
CFRP（炭素繊維強化プラスチック）の焼却処理に関する研究（燃焼過程の詳細観察）
石野洋二郎，田畑まどか，當山良太
第28回環境工学総合シンポジウム2018 日本機械学会
Event date： 2018.07
Language：Japanese Presentation type：Oral presentation (general)
Venue：早稲田大学
炭素繊維強化プラスチック（CFRP）は軽量かつ高強度のため，航空機や自動車などに多用されており，今後の利用量の増大に備え，難燃性CFRPの最終焼却処分方法について検討する必要がある．本研究（１）では，CFRP，とくに炭素繊維CFが，3000℃を超える高温燃焼ガスであっても全く燃焼しないこと，しかし，酸素流領域では極めて明瞭に燃焼・焼却することが確認され，温度条件よりはむしろ，高濃度酸素条件がCFRPの燃焼・焼却に有効であることを示した．本報では，はじめに前報（１）の結果，すなわち，試験片としてプラスチック成分を燃焼除去したCFRP（CFRP-Pと記載）の細板と，構造がより単純なグラファイト細径円柱（"G"FCR : "Graphite" Fine Cylindrical Rod，シャープペンシル替芯（太さ0.3, 0.5, 0.7 mm））とを使用し，酸素燃焼実験を行った結果を記載する．"G"FCRの燃焼特性の理解ならびに解析手法は，CFRPの燃焼解析の際に利用できるので，本報ではさらに，"G"FCR周囲の燃焼ガス流動の観察，"G"FCR表面の赤熱状況撮影および赤熱画像のRGB分解を行った．
-
Schlieren 3D-CT Measurement of Instantaneous Equivalence Ratio Distribution of Premixed Gas Field with Multiple Unknown Fuels
Event date： 2018.07
Language：Japanese Presentation type：Oral presentation (general)
-
CT ( COMPUTER TOMOGRAPHY ) MEASUREMENT OF 3D DENSITY DISTRIBUTIONS OF HIGH-SPEED PREMIXED TURBULENT FLAMES ( MULTI-PATH INTEGRATION IMAGE-NOISE REDUCTION TECHNIQUE BASED ON NOVEL CONCEPT OF COMPLEX BRIGHTNESS GRADIENT IN QUANTITATIVE SCHLIEREN IMAGES ) International conference
A. Z. Nazari, Y. Ishino, R. Yamada, T. Motohiro, F. Ito, H. Kondo, Y. Miyazato, S. Nakao
18th International Symposium on Flow Visualization
Event date： 2018.06
Language：English Presentation type：Oral presentation (general)
Venue：Zurich, Switzerland
The 20-directional observation of high-speed premixed turbulent flames, non-uniform density flow, by employing non-scanning 3D-CT (three-dimensional computer-tomography) technique using a delicate multi-directional quantitative schlieren system has been conducted. The 3D density distributions data of target flames by using ML-EM (Maximum Likelihood-Expectation Maximization) an appropriate CT algorithm are successfully reconstructed. First, the report deals with introducing a new approach for noise reduction in projections (density thickness) images of CT called "multi-path integration" novel technique. The numerical simulation results approve that the new approach is a good technique for noise reduction in projections images of CT. Next, by using inverse process for 3D density distributions data of high speed turbulent flame the 20-directional horizontal (x-directional) and vertical (z-directional) brightness gradient of schlieren images reconstructed. Then, by employing the new technique, the new set of projections images of density thickness successfully obtained. Finally, by using the new set of density thickness images "with decreased noise" as projections for CT reconstruction, the 3D density distributions data of target flame successfully reconstructed. The results validate that the "multi-directional integration" novel technique is a good technique for noise reduction in obtaining projections (density thickness) images of CT and the 3D density distributions of CT result.
-
Schlieren CT Measurement of 3D Density Distributions of Flame Kernels of Spark-Ignited Direct-Injection of Free, Cavity-Guided and Plane-Guided Fuel Jets International conference
Ahmad Zaid Nazari, Yojiro Ishino, Takanori Motohiro, Ryoya Yamada, Yuta Ishiko, Yu Saiki
11th Asia-Pacific Conference on Combustion
Event date： 2017.12
Language：English Presentation type：Oral presentation (general)
Venue：The University of Sydney, NSW Australia
-
COMPUTER FLOW VISUALIZATION OF UNDEREXPANDED JETS FROM AXISYMMETRIC SUPERSONIC MICRO NOZZLES International conference
H. FUKUDA, H. MAEDA, D. ONO, S. NAKAO, Y. MIYAZATO, Y. ISHINO
11th Pacific Symposium on Flow Visualization and Image Processing
Event date： 2017.12
Language：English Presentation type：Oral presentation (general)
Venue：Kumamoto
-
Rainbow schlieren measurements in underexpanded jets from square supersonic micro nozzles International conference
Hiroaki Maeda, Hikaru Fukuda, Shinichiro Nakao, Yoshiaki Miyazato, Yojiro Ishino
Experimental fluid mechanics 2017
Event date： 2017.11
Language：English Presentation type：Oral presentation (general)
Venue：Mikulov (Czech Republic)
-
Study of Fee Jets from Axisymmetric Supersonic Micro Nozzles (Part 1, Quantitative Flow Visualization) International conference
Hikaru Fukuda, Shinichiro Nakao, Yoshiaki Miyazato, Yojiro Ishino
14th International Conference on Flow Dynamics
Event date： 2017.11
Language：English Presentation type：Oral presentation (general)
Venue：Sendai
-
Study of Fee Jets from Axisymmetric Supersonic Micro Nozzles (Part 2, RANS Simulation) International conference
Hikaru Fukuda, Shinichiro Nakao, Yoshiaki Miyazato, Yojiro Ishino
14th International Conference on Flow Dynamics
Event date： 2017.11
Language：English Presentation type：Oral presentation (general)
Venue：Sendai
-
無振動回転式SLPエンジンの発明・開発・改良
石野洋二郎，丹羽智哉，杉浦秀隆，大沼燦汰，齋木悠
名工大テクノフェア 名古屋工業大学
Event date： 2017.11
Language：Japanese Presentation type：Poster presentation
Venue：名古屋工業大学
-
CFRP（炭素繊維強化プラスチック）の燃焼廃棄処理と燃焼加工法に関する研究
石野洋二郎，當山良太，田畑まどか，齋木悠
名工大テクノフェア 名古屋工業大学
Event date： 2017.11
Language：Japanese Presentation type：Poster presentation
Venue：名古屋工業大学
-
THREE-DIMENSIONAL FLAME STRUCTURE AND CHARACTERISTICS International conference
Y. Kato, T. Hirasawa, Z. Diao, M. Winter, Y. Ishino
the Ninth JSME-KSME Thermal and Fluids Engineering Conference 日本機械学会，韓国機械学会
Event date： 2017.10
Language：English Presentation type：Oral presentation (general)
Venue：沖縄コンベンションセンター
-
SCHLIEREN CT MEASUREMENT OF 3D DENSITY DISTRIBUTIONS OF PERFECTLY AND IMPERFECTLY EXPANDED SUPERSONIC MICRO-JETS FROM CIRCULAR AND RECTANGULAR MICRO NOZZLES International conference
A. Z. Nazari, Y. Ishino1, Y. Ishiko, T. Motohiro, R. Yamada, Y. Saiki, Y. Miyazato, S. Nakao
The Ninth JSME-KSME Thermal and Fluids Engineering Confference(TFEC9) 日本機械学会，韓国機械学会
Event date： 2017.10
Language：English Presentation type：Oral presentation (general)
Venue：沖縄コンベンションセンター
-
Schlieren 3D-CT Measuremsnt of Instantaneous Density Distributions of the Fuel Jets and Flame Kernel in a Direct-Injection Engine Model and Supersonic Jets Invited
Event date： 2017.09
Language：English Presentation type：Oral presentation (general)
-
THREE-DIMENSIONAL FLAME STRUCTURE AND CHARACTERISTICS OF HEATING PARTICLES IN METHANE CLUSTERED MICROFLAMES ON SIX FUEL AND ONE AIR JETS
Y. Kato, T. Hirasawa, Z. Diao, M. Winter, Y. Ishino
第26回日本エネルギー学会大会 日本エネルギー学会
Event date： 2017.08
Language：Japanese Presentation type：Poster presentation
Venue：名古屋
-
Study on CFRP(Carbon Fiber Reinforced Plastic) Combustion for Incineration(Observations of Combustion Processes of Test Pieces of CFRP)
Event date： 2017.07
Language：Japanese Presentation type：Oral presentation (general)
-
Schlieren 3D-CT Measurement of Instantaneous Density Distributions of Fuel Jet and Flame Kernel in a Direct-Injection Engine Model
Event date： 2017.07
Language：Japanese Presentation type：Oral presentation (general)
-
SLPローターエンジンの構造と作動特性
石野 洋二郎，丹羽 智哉，酒井 悠，熊野 聖人
第27回内燃機関シンポジウム 日本機械学会，自動車技術会
Event date： 2016.12
Language：Japanese Presentation type：Oral presentation (general)
Venue：東京工業大学，蔵前会館
本研究では，従来のWankel式ロータリーエンジンやピストンエンジンと異なり，主なシール機構がケーシング上に固定され，より確実に作動流体のシールを行うことができ，低振動である回転式エンジン「S.L.P (Single Lobe Peritrochoid：単葉ペリトロコイド)ローター・エンジン」を新たに考案した．本報では，エンジンの基本構成，作動原理，試作エンジンの構造，モーター駆動時における火炎伝播過程を報告する．
-
無振動回転式エンジン(SLPエンジン，日の丸エンジン)の発明
石野 洋二郎，丹羽 智哉，熊野 聖人
名工大・名市大合同テクノフェア 名古屋工業大学
Event date： 2016.11
Language：Japanese Presentation type：Oral presentation (general)
Venue：名古屋工業大学
容積型の回転式エンジンは，その低振動性から，電気自動車用の航続距離延長用発電機や非常用発電機などの用途に適するため，将来的にも需要が期待される．先行研究では，高度な低振動性を求め，純粋回転のみで作動する2ローター式の回転式エンジンを考案し，試作機による実機試験を行った．その結果，作動流体のシール性の向上が課題として挙げられた．そこで本研究では，従来のWankel式ロータリーエンジンやピストンエンジンと異なり，主なシール機構がケーシング上に固定され，より確実に作動流体のシールを行うことのできる回転式エンジン「S.L.P (Single Lobe Peritrochoid：単葉ペリトロコイド)ローター・エンジン」を新たに発明した．発表では，エンジンの基本構成，作動原理，試作エンジンの構造，燃焼過程について，報告する．
-
Schlieren 3D-CT Measurement of Instantaneous Density Distributions of the Shock-cell Structure of Under-expanded Supersonic Micro-jet International conference
Ahmad Zaid NAZARI, Yojiro ISHINO, Yuta ISHIKO, Yoshiaki MIYAZATO, Shinichiro NAKAO
2016 Asia-Pacific International Symposium on Aerospace Technology The Japan Society of Aeronautical and Space Sciences
Event date： 2016.10
Language：English Presentation type：Oral presentation (general)
Venue：富山国際会議場
Measurement of instantaneous density distribution of the shock-cell structure of an underexpanded supersonic microjet escaping into an ambient space from an axisymmetric convergent-divergent (Laval) micro nozzle has been conducted. For 3D observation of supersonic microjet, non-scanning 3D-CT technique using a multi-directional quantitative schlieren system with flash light source is employed. In this technique, for simultaneous schlieren photography, the custom-made 20-directional schlieren camera has been constructed and used. This study examines underexpanded supersonic jet from a micro nozzle with nozzle pressure ratio (NPR) 5.0 and plenum chamber pressure (stagnation pressure) 0.505 MPa. This micro nozzle design Mach number is Md = 1.5 and has circular cross-section with an exit diameter of 1000μm. First, the report deals with the density distribution. The density contour plot data of the jet flow is obtained by 3D-CT (Three Dimensional Computer Tomography) reconstruction of the images by MLEM an appropriate CT algorithm. Next, the density distribution data is calculated by formula. Theoretical results based on the theory of Tam (1984) are found to compare favorably with experimental measurement. The measured and calculated results are in acceptable agreement.
-
Development and Fundamental Study on a Novel Rotational Internal Combustion Engine with a Single-Lobe Peritrochoid Rotor International conference
Yojiro Ishino, Yu Sakai, Tomoya Niwa, Masato Kumano
2016 Asia-Pacific International Symposium on Aerospace Technology The Japan Society of Aeronautical and Space Sciences
Event date： 2016.10
Language：English Presentation type：Oral presentation (general)
Venue：富山国際会議場
A novel rotational internal combustion engine is invented and investigated for APU(Auxiliary power unit) of aircrafts and range-extender-power-unit for electric automobiles. For the applications, IC engines are required vibration-free characteristics. In the present engine, no reciprocating component is used, resulting in vibration-free operation. This engine mainly consists of a rotor casing, a rotor and a crank shaft. The rotor shapes as single lobe peritrochoid (S.L.P.) curve. The rotor rotates by the crank shaft of eccentricity e and rotates itself in counter-direction by phasing gears. The rotor casing shape having two cavities is defined as envelope curve of the rotating single-lobe peritrochoid rotor. The room between the rotor and casing performs the working processes for working gas; intake, compression, ignition, expansion and exhaust processes. The intake of premixed gas of air and fuel and exhaust of burnt gas are controlled by rotary valves installed on the combustion recesses of the rotor-casing. The combustion recesses are equipped with spark-electrodes for ignition. One of advantages of this engine compared with Wankel rotary engines and a previous engine invented by authors, is easy and reliable sealing of working gas. In this engine configuration, that is, a sealing component is only installed on waist section of rotor-casing, instead of complex sealing system on a rotor in case of Wankel engines, resulting in high efficiency by low-leakage of working gas.
In this paper, first, configuration and geometries of this engine are described. Next the prototype engine is introduced and the cyclic behavior of the working process of this prototype engine is explained. Performance of the prototype engine driven by an electric motor is also shown. -
Combustion Characteristics of Active Controlled Biogas Flames with Miniature Actuators
Masahiro KURODA, Takuma AKAO, Yu SAIKI, Yojiro ISHINO
Event date： 2016.10
Language：Japanese Presentation type：Oral presentation (general)
-
Schlieren 3D-CT Measuremsnt of Instantaneous Density Distributions of the Shock-cell Structure of Under-Expanded Supersonic Jets
Ahmad Zaid NAZARI, Naoki HAYASHI, Yuta ISHIKO, Kimihiro NAGASE, Kazuma KAKIMOTO, Yojiro ISHINO, Yoshiaki MIYAZATO, Shinichiro NAKAO
Event date： 2016.09
Language：Japanese Presentation type：Oral presentation (general)
-
Instantaneous 3D-CT(Computer Tomography) measurements with instantaneous multi-directional photography for unsteady flame/flow phenomena; and 3D printing of 3D reconstructed distributions Invited
Yojiro ISHINO
Event date： 2016.09
Language：Japanese Presentation type：Oral presentation (general)
-
新型回転式無振動内燃エンジン「日の丸エンジン」の開発
石野 洋二郎，丹羽 智哉，熊野 聖人
イノベーション・ジャパン2016‐大学見本市 新エネルギー・産業技術総合開発機構（NEDO），科学技術振興機構（JST）
Event date： 2016.08
Language：Japanese Presentation type：Poster presentation
Venue：東京ビッグサイト
現在の主流の往復運動のピストンエンジンは，無振動化が困難である．本発明の無振動回転エンジン「日の丸エンジン」は，より単純な単葉ペリトロコイドローター（準円形）と２凹部のケーシングにより構成される最も単純な構造のエンジンである．
-
3D Printing of Spark-Ignited Flame Kernels, Experimentally Captured by 3D-Computer Tomography and Multi-Directional Schlieren Photography Invited International conference
Yojiro Ishino, Naoki Hayashi, Yuta Ishiko, Kimihiro Nagase, Kazuma Kakimoto, Ahmad Zaid Nazari, Yu Saiki
ASME 2016 Summer Heat Transfer Conference American Society of Mechanical Engineeres
Event date： 2016.07
Language：English Presentation type：Oral presentation (general)
Venue：Washington DC
Non-scanning 3D-CT(Computer Tomography) technique employing a multi-directional quantitative schlieren photographic system with flash light source, has been performed to obtain instantaneous density distributions of spark-ignited laminar / turbulent flame kernels. For simultaneous schlieren photography, the custom-made 20-directional schlieren camera was constructed and used. The flame kernels are made by spark ignition for a fuel-rich propane-air premixed gas (flow velocity :1.0 m/s, equivalence ratio :1.4 ). Spark electrodes of 0.4 mm diameter with 1.0 mm gap are used. First, development of laminar flame kernel is indicated in the 1st row high-speed image of top right. 3D printed model of the CT reconstruction result show the spherical shape of flame kernel with a pair of deep wrinkles. The wrinkle is considered to be caused by spark electrodes. Next turbulent flame kernel behind turbulence promoting grid is selected (trubulence intensity 0.26 m/s). Second row high-speed images of top-right show corrugated flame shape. 3D model of CT result expresses the instantaneous 3D turbulent flame kernel shapes. These 3D solid models are 3D-printed as 2 times large size for threshold density level of 0.7 kg/m3.
-
Schlieren 3D-CT Reconstruction of Instantaneous Ddensity Distributions of Spark-Ignited Flame Kerness of Fuel-Rich Propane-Air Premixture International conference
Yojiro Ishino, Naoki Hayashi, Yuta Ishiko, Ahmad Zaid Nazari, Kimihiro Nagase, Kazuma Kakimoto, Yu Saiki
ASME 2016 Summer Heat Transfer Conference American Society of Mechanical Engineeres
Event date： 2016.07
Language：English Presentation type：Oral presentation (general)
Venue：Washington DC
For 3D observation of high speed flames, non-scanning 3D-CT technique using a multi-directional quantitative schlieren system with flash light source, is proposed for instantaneous density distribution of unsteady premixed flames. This "Schlieren 3D-CT" is based on (i)simultaneous acquisition of flash-light schlieren images taken from numerous directions, and (ii) 3D-CT reconstruction of the images by an appropriate CT algorithm. In this technique, for simultaneous schlieren photography, the custom-made 20-directional schlieren camera has been constructed and used. This camera consists of 20 optical systems of single-directional quantitative schlieren system. Each system is composed of two convex achromatic lenses of 50 mm in diameter and 300 mm in focal length, a light source unit, a schlieren stop of a vertical knife edge and a digital camera. The light unit has a flash (9 micro-sec duration) light source of a uniform luminance rectangular area of 1 mm x 1 mm. Both of the uniformity of the luminosity and the definite shape are essential for a quantitative schlieren observation. Sensitivity of the digital cameras are calibrated with a stepped neutral density filter. Target flames are located at the center of the camera. The image set of 20 directional schlieren images are processed as follows. First the schlieren picture brightness is shifted by no-flame-schlieren picture brightness in order to obtain the real schlieren brightness images. Second, brightness of these images is scaled by Gladstone-Dale constant of air. Finally, the scaled brightness is horizontally integrated to form "density thickness images", which can be used for CT reconstruction of density distribution. The density thickness images are used for CT reconstruction by MLEM (maximum likelihood-expectation maximization) CT-algorithm to obtain the 3D reconstruction of instantaneous density distribution. In this investigation, the "density thickness" projection images of 400(H) x 500(V) pixel (32.0 mm x 40.0 mm) are used for 3D-CT reconstruction to produce 3D data of 400(x) x 400(y) x 500(z) pixel (32.0 mm x 32.0 mm x 40.0 mm). The voxel size is 0.08 mm each direction. In this investigation, the target flame is spark-ignited flame kernels. The flame kernels are made by spark ignition for a fuel-rich propane-air premixed gas. First, laminar flow is selected as the premixed gas flow to establish the spherically expanding laminar flame. The CT reconstruction result show the spherical shape of flame kernel with a pair of deep wrinkles. The wrinkle is considered to be caused by spark electrodes. Next turbulent flows behind turbulence promoting grid is selected. The corrugated shape flame kernel is obtained. The schlieren 3D-CT measurements are made for the complicated kernels. CT results expresses the instantaneous 3D turbulent flame kernel shapes.
-
Study on a Novel Rotational Internal Combustion Engine with a S.L.P. Rotor
Yojiro ISHINO, Yu SAKAI, Tomoya NIWA
Event date： 2016.06 - 2016.07
Language：Japanese Presentation type：Oral presentation (general)
-
Study on Micro-Flame Array Burner for a Gas Cooking Stove Adapted to Finned Heating Surface
Ryota TOYAMA, Yasuyuki KONDO, Yojiro ISHINO
Event date： 2016.06 - 2016.07
Language：Japanese Presentation type：Oral presentation (general)
-
Fundamental Configuration and Characteristics of a Novel Rotational Internal Combustion Engine with a S.L.P. Rotor
Yojiro ISHINO, Yu SAKAI, Tomoya NIWA
Event date： 2016.06
Language：Japanese Presentation type：Oral presentation (general)
-
S.L.P.ローターを用いた新型回転式エンジンに関する研究
石野 洋二郎，酒井 悠
日本機械学会 東海支部 第65期総会・講演会 日本機械学会 東海支部
Event date： 2016.03
Language：Japanese Presentation type：Oral presentation (general)
Venue：愛知工業大学
本機関は，特殊曲線により形成されるローター，および，それらを内包するケーシングから構成される内燃機関である．ピストンおよびコンロッドなどの往復運動を行う部品を有さないため，低振動であることを構造的特長とする．作動流体のシールについては，回転ローター上にシール部品が設置されるバンケル・エンジンと異なり，本新型エンジンでは，ケーシングに固定されたシール部品により実施される．本発表では，本新型エンジンの作動原理および特長について報告を行う．
-
20方向シュリーレン三次元CT計測による乱流予混合気流中の火花点火火炎の成長過程の観察
永瀬公博，林直樹，石河雄太，Ahmad Zaid Nazari，柿本和摩，齋木悠，石野洋二郎
日本機械学会東海支部 第65期総会・講演会 日本機械学会 東海支部
Event date： 2016.03
Language：Japanese Presentation type：Oral presentation (general)
Venue：愛知工業大学
本研究では，多方向シュリーレンカメラにより獲得した定量シュリーレン画像群から得られる「偏差密度厚さ分布画像」群をプロジェクションデータとする三次元CT法により瞬間三次元密度分布を獲得する手法を提案した．本報では，20組のシュリーレン光学系から構成される20方向シュリーレン・カメラを使用し，乱流予混合気中において火花点火により得られた火炎核の三次元密度分布の三次元CT再構成を行い，その成長過程の観察を行った．
-
バイオガス燃焼における排出ガス特性の能動制御および火炎温度計測
赤尾 拓磨，黒田 雅浩，齋木 悠，石野 洋二郎
日本機械学会東海支部 第65期総会・講演会 日本機械学会 東海支部
Event date： 2016.03
Language：Japanese Presentation type：Oral presentation (general)
Venue：愛知工業大学
-
20方向シュリーレン三次元CT計測による火花点火球面伝播火炎の成長過程の観察
石河 雄太，林 直樹，Ahmad Zaid Nazari，永瀬 公博，柿本 和摩，齋木 悠，石野 洋二郎
第53回燃焼シンポジウム 日本燃焼学会
Event date： 2015.11
Language：Japanese Presentation type：Oral presentation (general)
Venue：筑波
本研究では，多方向シュリーレンカメラにより獲得した定量シュリーレン画像群から得られる「偏差密度厚さ分布画像」群をプロジェクションデータとする三次元CT法により瞬間三次元密度分布を獲得する手法を提案した．本報では，20組のシュリーレン光学系から構成される20方向シュリーレン・カメラを使用し，予混合気中において火花点火により得られた球面伝播火炎の三次元密度分布の三次元CT再構成を行い，その成長過程の観察を行った．
-
亜酸化窒素／エタノールを推進剤とする小型液体ロケットエンジンの開発
西山 典，丸橋 明恵，石河 雄太，林 直樹，加藤 義春，野口 好夫，石野 洋二郎
第53回燃焼シンポジウム 日本燃焼学会
Event date： 2015.11
Language：Japanese Presentation type：Poster presentation
Venue：筑波
本研究では，酸化剤に亜酸化窒素，燃料にエタノールを推進剤として用いる小型液体ロケットエンジンの開発を行う．本エンジンは，推力220kgf，スロート直径40mmの小型ロケットエンジンであり，宇宙空間でのスラスターとしての使用を主目的とするが，弾道軌道でのロケット打ち上げも計画されている．本報では，2015年3月に行った，1/5負荷のエンジン燃焼実験の結果を報告する．
-
町工場との小型ロケットの共同開発・打ち上げ計画（ロケットエンジンの部分負荷燃焼試験）
石野 洋二郎，西山 典，丸橋明恵，林 直樹，石河 雄太，加藤 義春，野口 好夫
名工大・名市大合同テクノフェア
Event date： 2015.10
Language：Japanese Presentation type：Poster presentation
Venue：名古屋工業大学
-
噴出速度の異なる高速乱流バーナー火炎の瞬間三次元密度分布の２０方向シュリーレンＣＴ計測と３Ｄプリンティング
石河雄太，林直樹，Abd Razak Ili Fatimah，齋木悠，石野洋二郎
可視化情報全国講演会（京都２０１５） 可視化情報学会
Event date： 2015.10
Language：Japanese Presentation type：Oral presentation (general)
Venue：京都工芸繊維大学
本研究では，これまでの研究を拡張し，予混合火炎に対し多方向から定量シュリーレン撮影を実施し，空間積分処理により密度厚さ分布画像を作成し，三次元CT処理により三次元密度分布を得る，新たな計測法を提案する．本報では，「20方向マルチ・シュリーレンカメラ」を用いて，異なる噴出速度の高速乱流バーナー火炎の瞬間三次元密度分布の三次元CT再構成を実施した．さらに，3Ｄプリンターを用いて，乱流火炎の瞬間形状の三次元立体モデル３）の製作を行った．
-
２０方向シュリーレン三次元CT計測による火花点火球面伝播火炎の成長過程の観察
林 直樹, 石河 雄太, NAZARI Ahmad Zaid,永瀬 公博, 柿本 和摩, 齋木 悠, 石野 洋二郎
東海燃焼セミナー 東海燃焼セミナー
Event date： 2015.09
Language：Japanese Presentation type：Poster presentation
Venue：名古屋工業大学
-
Manipulation of large-scale vortical structures and mixing in a coaxial jet with miniature jet actuators International conference
Y. Saiki, S. Tanaka, S. Hattori, K. Nakura and Y. Ishino
8th International Symposium on Turbulence, Heat and Mass Transfer (THMT'15)
Event date： 2015.09
Language：English Presentation type：Oral presentation (general)
Venue：Sarajevo
-
先端技術フォーラム．多方向同時画像計測装置と三次元ＣＴ処理による乱流火炎の瞬間形状獲得と３Ｄプリンティング
石野洋二郎
日本機械学会２０１５年度年次大会 日本機械学会
Event date： 2015.09
Language：Japanese Presentation type：Oral presentation (invited, special)
Venue：北海道大学
本研究では，これまでの研究を拡張し，予混合火炎に対し多方向から定量シュリーレン撮影を実施し，空間積分処理により密度厚さ分布画像を作成し，三次元CT処理により三次元密度分布を得る，新たな計測法を提案する．本報では，「20方向マルチ・シュリーレンカメラ」を用いて，異なる噴出速度の高速乱流バーナー火炎の瞬間三次元密度分布の三次元CT再構成を実施した．さらに，3Ｄプリンターを用いて，乱流火炎の瞬間形状の三次元立体モデルの製作を行った．
-
3D-CT Measurement of Instantaneous Density Distributions of High-Speed Premixed Turbulent Burner Flames with a Multi-Directional Schlieren Camera (Effects of Flow Velocity on 3D Flame Front Shape) International conference
Yojiro Ishino, Naoki Hayashi, Ili Fatimah Bt Abd Razak, Yu Saiki
The 1st Thermal and Fluid Engineering Summer Conference American Society of Thermal and Fluids Engineering
Event date： 2015.08
Language：English Presentation type：Oral presentation (general)
Venue：New York
In present study, in order to provide a suitable technique for 3D observation of high speed turbulent flames, non-scanning 3D-CT technique using a multi-directional quantitative schlieren system with flash light source, is proposed for instantaneous density distribution of unsteady premixed flames. This "Schlieren 3D-CT" is based on (i)simultaneous acquisition of flash-light schlieren images taken from numerous directions, and (ii) 3D-CT reconstruction of the images by an appropriate CT algorithm. For simultaneous schlieren photography, in this experiment, the custom-made 20-directional schlieren camera has been constructed and used. Target flames are located at the center of the camera. The image set of 20 directional schlieren images are processed by MLEM CT-algorithm to obtain the 3D reconstruction of instantaneous density distribution. In this investigation, the target turbulent flame is high-speed burner flames. The burner has a nozzle exit of 4.2 mm diameter. The average flow velocity of the propane-air mixture of equivalence ratio of 1.1 is set to be 4, 6, 8 and 10 m/s. The burner is equipped with a turbulence promoting orifice in the burner tube. In order to anchor the high-speed flame on the burner nozzle, the burner tip has 4 holes for introducing the pilot flames. Results of the 3D-reconstructions indicates that the distributions show the complicated shape of the high speed turbulent flames. It is also found that the flame structure of higher speed flame has fine scale corrugations. This corresponds to the "corrugated flamelets regime" of the Borghi & Peters diagram for premixed turbulent combustion well.
-
3D Printing of Instantaneous Turbulnet Flame Shapes, Experimentally Captured by 3D-Computer Tomography and Multi-Directional Schlieren Photography International conference
Yojiro Ishino, Naoki Hayashi, Yuta Ishiko, Ili Fatimah Bt Abd Razak, Yu Saiki, Kimihiro Nagase, Kazuma Kakimoto
The 1st Thermal and Fluid Engineering Summer Conference American Society of Thermal and Fluids Engineering
Event date： 2015.08
Language：English Presentation type：Oral presentation (general)
Venue：New York
-
3D-CT Measurement of Instantaneous Density Distribution of High Speed Turbulent Burner with 20 Directional Schlieren Camera(Effects of Nozzle Exit Velocity on Flame Shape)
TOKAI ENGINEERING COMPLEX 2015 (TEC15)
Event date： 2015.03
Language：Japanese Presentation type：Oral presentation (general)
-
Multi(20)-Directional Schlieren 3D-CT Measurement of Instantaneous 3D Density Distributions of a High Speed Turbulent Burner Flame
Event date： 2014.12
Language：Japanese Presentation type：Oral presentation (general)
-
Novel Measuring Technique of Instantaneous 3D Density Distributions of Unsteady Premixed Flames (Multi-Schlieren 3D-CT Measurement of High Speed Turbulent Burner Flames)
Event date： 2014.11
Language：Japanese Presentation type：Oral presentation (general)
-
町工場とのロケット共同打ち上げ計画（亜酸化窒素／エタノール ロケットエンジンの開発）
石野 洋二郎，西山 典，林 直樹，石河 雄太，加藤 義春，野口 好夫
名工大・名市大合同テクノフェア 名古屋工業大学・名古屋市立大学
Event date： 2014.10
Language：Japanese Presentation type：Oral presentation (general)
Venue：名古屋工業大学
-
選択的混合操作を通じた模擬バイオガス燃焼の能動制御
黒田雅浩，名倉香純，齋木悠，石野洋二郎
第137回東海燃焼セミナー 東海燃焼セミナー
Event date： 2014.09
Language：Japanese Presentation type：Poster presentation
Venue：名古屋大学
-
新型・非偏心回転式エンジンの開発
酒井悠，藤井博之，山本優作，齋木悠，石野洋二郎
第137回東海燃焼セミナー 東海燃焼セミナー
Event date： 2014.09
Language：Japanese Presentation type：Oral presentation (general)
Venue：名古屋大学
-
町工場とのロケット共同打ち上げ計画（亜酸化窒素／エタノール ロケットエンジンの開発） International conference
石野洋二郎，西山典，林直樹，石河雄太，加藤義春，野口好夫
第137回東海燃焼セミナー 東海燃焼セミナー
Event date： 2014.09
Language：Japanese Presentation type：Poster presentation
Venue：名古屋大学
-
20方向マルチ・シュリーレンカメラによる高速実用バーナー火炎の瞬間密度分布の計測
林直樹，Ili Fatimah Bt Abd Razak，齋木悠，石野洋二郎
第137回東海燃焼セミナー 東海燃焼セミナー
Event date： 2014.09
Language：Japanese Presentation type：Poster presentation
Venue：名古屋大学
-
3D-CT Measurement of an Instantaneous Density Distribution of a Turbulent Premixed Flame with a Multi-Directional Quantitative Schlieren Camera International conference
Yojiro Ishino, Takahiro Kato, Yudai Kurimoto1 and Yu Saiki
10th International ERCOFTAC Symposium on Engineering Turbulence Modelling and Measurements ERCOFTAC
Event date： 2014.09
Language：English Presentation type：Oral presentation (general)
Venue：Spain
-
多方向シュリーレン三次元CT法による非定常予混合火炎の瞬間三次元密度分布の獲得（高速乱流バーナー火炎の計測）
石野 洋二郎，加藤 貴裕，栗本 雄大，齋木 悠，近藤 靖幸，林 直樹
日本機械学会2014年度年次大会 日本機械学会
Event date： 2014.09
Language：Japanese Presentation type：Oral presentation (general)
Venue：東京，東京電機大学
本研究では，これまでに多方向定量シュリーレン撮影により予混合火炎の輝度分布を獲得し，その輝度分布を空間積分することで密度偏差厚さの獲得を行い，獲得された画像をプロジェクション画像として，三次元CT法により再構成することで三次元密度分布の獲得を行ってきた．本発表では，定量シュリーレンCT法の計測原理および20台のシュリーレン光学系からなるカメラにより撮影された実用バーナーの高速予混合火炎の瞬間三次元密度分布の三次元CT再構成の結果を報告する．
-
融合中のマイクロフレーム群を対象としたCH*発光に基づくCT法による３次元火炎形状計測
有賀雄大，平沢太郎，林直樹，石野洋二郎
日本実験力学会2014年次講演会 日本実験力学会
Event date： 2014.08
Language：Japanese Presentation type：Oral presentation (general)
Venue：兵庫県立大学 工学部 姫路キャンパス
-
Multi-Directional Schlieren 3D-CT Measurement of Instantaneous 3D Density Distributions of High Speed Turbulent Burner Flames
Event date： 2014.05
Language：English Presentation type：Oral presentation (general)
-
厨房作業者にやさしい新型ガスコンロの開発・評価
林直樹，水野雄太，近藤靖幸，鹿島彰浩，茂木徹，十河桜子，成田先和，安田益雄，石野洋二郎
第６３期総会・講演会 日本機械学会東海支部
Event date： 2014.03
Language：Japanese Presentation type：Oral presentation (general)
Venue：大同大学
本研究では，厨房作業者の快適性向上を念頭に置き，火炎および燃焼ガスが厨房作業者から離れる方向に流れる方式（後方火炎型）のガスコンロを設計し，その試作を行った．また，本研究では，計測装置（"モックアップ"）による，コンロが周囲に与える熱授与の計測と，広範囲高温ガス流動観察システムによる燃焼ガスの可視化を同時に行うことで，視覚的，数値的にコンロの評価することができる計測システムを提案し，これを用いて，試作ガスコンロと比較コンロについて比較実験を行い，快適性向上の達成度合いを評価する．
-
非偏心回転式エンジンの開発（点火燃焼過程の可視化観察）
酒井 悠，手嶋 啓介，藤井 博之，山本 優作，齋木 悠，石野 洋二郎
第63期総会・講演会 日本機械学会東海支部
Event date： 2014.03
Language：Japanese Presentation type：Oral presentation (general)
Venue：大同大学
本機関は，2種類の特殊曲線により形成されるローター，および，それらを内包するケーシングから構成される内燃機関である．純回転による作動の実現により，低振動という構造的特長を有し，また，ケーシングとの隙間を微小に保ち，非接触シールの実現を目指す．容積型エンジンでありながら，純回転により作動し，従来エンジンとガスタービンエンジンの中間の新カテゴリーとなる可能性を秘めている．本発表では，第２試作エンジンの機関構成，ならびに高速度カメラによる点火燃焼過程の可視化観察結果を報告する．
-
多方向定量シュリーレン三次元CT法による乱流予混合火炎の瞬間三次元密度分布の計測
栗本雄大，加藤貴裕，齋木悠，石野洋二郎
第63期総会・講演会 日本機械学会東海支部
Event date： 2014.03
Language：Japanese Presentation type：Oral presentation (general)
Venue：大同大学
多方向定量シュリーレン撮影により，予混合火炎の輝度分布を獲得し，その輝度分布を空間積分することで密度偏差厚さの獲得を行った．そして，獲得された密度偏差厚さをプロジェクション画像として，三次元CT法により再構成することで瞬間三次元密度分布の獲得を行った．本発表では，２０台のシュリーレン光学系からなるカメラにより，実用バーナーの高速乱流予混合火炎の撮影を行い，同火炎の瞬間三次元密度分布の三次元CT再構成の結果を報告する．
-
3D Solid Modeling of an Instantaneous Shape of a Turbulent Premixed Flame by 3D-Printing and Non-Scanning 3D-CT Measurement
Yojiro ISHINO, Takahiro KATO, Yudai KURIMOTO, Yu SAIKI
Event date： 2013.12
Language：Japanese Presentation type：Poster presentation
-
Multi-directional Schlieren 3D-CT measurement of Density Distribution of Premixed Flame
Takahiro KATO, Yudai KURIMOTO, Yu SAIKI, Yojiro ISHINO
Event date： 2013.12
Language：Japanese Presentation type：Oral presentation (general)
-
Development of an Novel Non-eccentric Rotational Engine "Ishino Engine"(Fundamental Configuration and Characteristics) International conference
Yojiro Ishino, Keisuke Teshima, Hiroyuki Fujii, Yusaku Yamamoto, Yu Saiki
19th Small Engine Technology Conference 日本自動車技術会&アメリカ自動車技術会
Event date： 2013.10
Language：English Presentation type：Oral presentation (general)
Venue：Taiwan
-
Study on a Non-eccentric Rotational Internal Combustion Engine
Event date： 2013.10
Language：Japanese Presentation type：Oral presentation (general)
-
Development of Non-eccentric Rotor IC Engine ''Ishino Engine''(High-speed Video Observations of Combustion Processes)
Keisuke TESHIMA, Hiroyuki FUJII, Yusaku YAMAMOTO, Yu SAIKI,Yojiro ISHINO
Event date： 2013.09
Language：Japanese Presentation type：Oral presentation (general)
-
Three-Dimensional-CT Measurement of Density and Light Intensity Distributions of Non-axisymmetric Premixed Flames International conference
Takahio KATO, Kenta HORIMOTO, Shoma ISHIGURO, Yu SAIKI,Yojiro ISHINO
Event date： 2013.09
Language：Japanese Presentation type：Oral presentation (general)
-
Three-Dimensional Reconstructions of Density and Light-Intensity Distributions of Non-axisymmetric Premixed Flames by Multi-directional Quantitative Schlieren 3D-CT Method
Takahiro KATO, Kenta HORIMOTO, Shoma ISHIGURO, Yu SAIKI, Yojiro ISHINO
Visualization Symposium 2013
Event date： 2013.07
Language：Japanese Presentation type：Oral presentation (general)
-
Development of Non-eccentric Rotor IC Engine "Ishino Engine"(High-speed Video Observations of Ignition and Flame Propagation Processes) International conference
Event date： 2013.07
Language：Japanese Presentation type：Oral presentation (general)
-
Thermal Enviroment Evaluation System for Burnt Gas Behavior and Thermal Strain for Kitchen Workers to Develop a New Gas Cooking Stove
Event date： 2013.07
Language：Japanese Presentation type：Oral presentation (general)
-
3D-CT Measurement of Three-Dimensional Density Distribution of Premixed Flames Using a Multi-Directional Quantitative-Schlieren Optical System International conference
Y. Ishino, K. Horimoto, T. Kato, S. Ishiguro, Y. Saiki
アジア太平洋航空宇宙技術科学会議2013
Event date： 2013.05
Language：English Presentation type：Oral presentation (general)
Venue：Taiwan
-
Multi-Directional Quantitative Schlieren Observations for 3D-CT Reconstruction of Three-Dimensional Density Distribution International conference
Yojiro Ishino, Kenta Horimoto, Takahiro Kato, Shoma Ishiguro, Yu Saiki
第９回アジア太平洋燃焼会議
Event date： 2013.05
Language：English Presentation type：Oral presentation (general)
Venue：Gyeongju Hilton, Gyeongju, Korea
-
A Novel Non-eccentric Rotation I.C. Engine "Ishino Engine"(Fundamental Configuration and Combustion Process) International conference
Yojiro Ishino, Keisuke Teshima, Yusaku Yamamoto, Hiroyuki Fujii, Yu Saiki
第９回アジア太平洋燃焼会議
Event date： 2013.05
Language：English Presentation type：Oral presentation (general)
Venue：Gyeongju Hilton, Gyeongju, Korea
-
Thermal Enviroment Evaluation System for Development of a New Gas Cooking Stove with Low Thermal Strain for Kitchen Workers
Event date： 2013.03
Language：Japanese Presentation type：Oral presentation (general)
-
Three-Dimensional-CT Measurement of Density Distribution of a Premixed Flame by Multi-Directional Quantitative Schlieren Observation
Syoma Ishiguro, Kenta Horimoto, Takahiro Kato, Yu Saiki, Yojiro Ishino
Event date： 2013.03
Language：Japanese Presentation type：Oral presentation (general)
-
非偏心回転式エンジン「イシノ・エンジン」の開発（機関構成の解説と点火燃焼過程の可視化観察）
山本 優作，手嶋 啓介，藤井 博之，石野 洋二郎
日本機械学会東海支部第62期総会・講演会
Event date： 2013.03
Language：Japanese Presentation type：Oral presentation (general)
-
新型・非偏心回転式容積型エンジン「イシノ・エンジン」の開発
石野 洋二郎，手嶋 啓介，藤井 博之，山本 優作
名工大・名市大合同テクノフェア，出品・講演
Event date： 2012.12
Language：Japanese Presentation type：Poster presentation
-
サイクロイド・ローターとトロコイド・ローターからなる新型非偏心回転式内燃エンジン「イシノ・エンジン」の開発（機関構成と体積変化過程）
手嶋 啓介，山本 優作，藤井 博之，齋木 悠，石野 洋二郎
第50回燃焼シンポジウム
Event date： 2012.12
Language：Japanese Presentation type：Oral presentation (general)
-
Prediction of Buoyant Behavior of Burnt Gas with Buoyant Vorticity(Flow Visualization Experiment and Numerical Simulation of a Spherical Flame by Discrete Vortex Method)
Event date： 2012.12
Language：Japanese Presentation type：Oral presentation (general)
-
非偏心回転式エンジン「イシノ・エンジン」の開発（２種類の特殊曲面ローターを用いた機関構成と体積変化過程）
手嶋 啓介，藤井 博之，山本 優作，石野 洋二郎
日本機械学会 熱工学コンファレンス201
Event date： 2012.11
Language：Japanese Presentation type：Oral presentation (general)
-
非偏心回転式内燃機関「イシノ・エンジン」の研究開発（機関構成・原理と作動特性）
石野 洋二郎，手嶋 啓介，藤井 博之，山本 優作
第23回内燃機関シンポジウム
Event date： 2012.10 - 2012.11
Language：Japanese Presentation type：Oral presentation (general)
-
特殊曲面ローターを用いた非偏心回転式エンジン「イシノ・エンジン」の機関構成と作動特性
石野 洋二郎，手嶋 啓介，山本 優作，藤井 博之
自動車技術会 秋期学術講演会
Event date： 2012.10
Language：Japanese Presentation type：Oral presentation (general)
-
新型・非偏心回転式容積型エンジン「イシノ・エンジン」の開発
石野 洋二郎
イノベーション・ジャパン，大学見本市．出品（大臣視察）
Event date： 2012.09
Language：Japanese Presentation type：Poster presentation
-
Time-series 3D-CT Measurement of Turbulent Premixed Flame with Multi-Mirror Optical System
Tahiro MIZOKAMI, Yuya OKITA, Yu SAIKI, Yojiro ISHINO
Event date： 2012.03
Language：Japanese Presentation type：Oral presentation (general)
-
Study on Novel Rotational I.C. Engine
Yojiro ISHINO, Keisuke TESHIMA, Yu SAIKI
Event date： 2012.03
Language：Japanese Presentation type：Oral presentation (general)
-
Experimental and Numerical Study on Prediction of Buoyant Behavior of Burnt Gas of a Spherical Flame by Buoyancy Vorticity
Mineto MITSUHASHI, Yu SAIKI, Yojiro ISHINO
Event date： 2012.03
Language：Japanese Presentation type：Oral presentation (general)
-
4D-CT Measurement of a Turbulent Premixed Flame by Simultaneous Multi-Directional High-Speed Photography with Multi-Mirror Optical Capture System International conference
Yojiro ISHINO, Yuya OKITA, Yu SAIKI, Tahiro MIZOKAMI
International Symposium on EcoTopia Science '11
Event date： 2011.12
Language：English Presentation type：Oral presentation (general)
-
Time-Series Multi-Dimensional Temperature Measurement at High Temperature Combustion Field with Heat Radiation Images of a Hi-Nicalon Fiber array - Improvement of the Time-Response by Compensation Procedure for a First-Order-Time-Lag of the System -
Yoya NAGANO, Keishi TANAKA, Yu SAIKI, Yojiro ISHINO
Event date： 2011.12
Language：Japanese Presentation type：Oral presentation (general)
-
Premixed Flame Propagation in High-Pressure Vortex Flows - Observation of Flame Behavior in a High-Rotational Cylindrical Closed Cuvette -
Takahiro IMAEDA, Yu SAIKI, Yojiro ISHINO
Event date： 2011.12
Language：Japanese Presentation type：Oral presentation (general)
-
Interaction between Multiple PET Resin Particles in Burning Processes by Abrupt Heating - Effects of Initial Separation Distance in Horizontal Configuration on the Interaction -
Yasuo OGURI, Toshiharu FUKAZAWA, Yu SAIKI, Yojiro ISHINO
Event date： 2011.12
Language：Japanese Presentation type：Oral presentation (general)
-
Premixed Flame Propagation in High-Pressure High-Rotational Vortex Flows
Takahiro IMAEDA, Yu SAIKI, Yojiro ISHINO
Event date： 2011.10
Language：Japanese Presentation type：Oral presentation (general)
-
Time-Series Multi-Dimensional Temperature Measurement of Turbulent Flames with Heat Radiation Images of a Hi-Nicalon Fiber Array - Improvement of the Time-Response by Compensation Procedure for a First-Order-Time-Lag of the System
Yoya NAGANO, Keishi TANAKA, Yu SAIKI, Yojiro ISHINO
Event date： 2011.10
Language：Japanese Presentation type：Oral presentation (general)
-
人間搭乗巨大二足歩行ロボットと 燃焼駆動跳躍ロボット
石野洋二郎，齋木悠，岩澤宏太，津田聖也，木下晶太，伊藤達也，田中健太郎
イノベーション・ジャパン2011大学見本市 科学技術振興機構，新エネルギー・産業技術総合開発機構
Event date： 2011.09
Language：Japanese
Venue：東京国際フォーラム
-
Study on Vertical Jumping Motion of Full-Scale Humanoid Robot with a Combustion Linear Actuator International conference
Kota IWASAWA, Yojrio ISHINO, Yu SAIKI
Event date： 2011.05
Language：Japanese Presentation type：Poster presentation
-
Human-Boarding Stable-Walking Large-Size Bipedal Robot( For Trial-Boarding on site )
Yojiro ISHINO, Kota IWASAWA, Yu SAIKI
Event date： 2011.05
Language：Japanese Presentation type：Poster presentation
-
Time-Resolved Multi-Dimensional Temperature Measurement of a Turbulent Flame with Heat Radiation from a Hi-Nicalon Fiber Array (Measurements of Instantaneous 2-Dimensional Temperature Distribution)
Keishi TANAKA, Yoya NAGANO, Yu SAIKI, Yojiro ISHINO
Event date： 2011.03
Language：Japanese Presentation type：Oral presentation (general)
-
Measurement of Local Burning Velocity distribution of a Turbulent Premixed Flame by Simultaneous 3D-CT Reconstruction with a 158-Lens Camera and Triple-Camera 3D-PTV
Kenta HORIMOTO, Yasufumi TOMIDA, Yosuke SHUKU, Yu SAIKI, Yojiro ISHINO
Event date： 2011.03
Language：Japanese Presentation type：Oral presentation (general)
-
燃焼を駆動力とする高機動性ロボット（ロボ・アスリート・プロジェクト）
石野 洋二郎
自動車技術会中部支部学生自動車研究会 2010年度研究発表会 自動車技術会中部支部
Event date： 2011.02
Language：Japanese Presentation type：Oral presentation (invited, special)
Venue：名古屋工業大学
燃焼を駆動力とする高機動性ロボットについて，新開発の燃焼式直動アクチュエータの動作特性や，搭載ロボットの跳躍挙動について発表した．また，燃焼により高機動性ロボットを実現する研究開発計画「ロボ・アスリート・プロジェクト」についての提唱・提言も行った．
-
Measurement of Time Series of a Turbulent Premixed Flame using by a Single high-speed Camera, Multi-mirror optical capture system, and 3-D CT reconstruction
Yuya OKITA, Yao XU, Kenta HORIMOTO, Yu SAIKI, , Yojiro ISHINO
Event date： 2010.12
Language：Japanese Presentation type：Oral presentation (general)
-
Measurement of Local Burning Velocity distribution of a Turbulent Premixed Flame by Simultaneous 3D-CT Reconstruction with a 158-Lens Camera and Triple-Camera 3D-PTV (Relationship between displacement of flame-front and velocity distribution of unburnt mixture)
Yasufumi TOMIDA, Yosuke SHUKU, Kenta HORIMOTO, Yu SAIKI, Yojiro ISHINO
Event date： 2010.12
Language：Japanese Presentation type：Oral presentation (general)
-
Time-Resolved Multi-Dimensional Temperature Measurement of a Turbulent Flame with Heat Radiation from a Hi-Nicalon Fiber Array (Measurements of Instantaneous 2-Dimensional Temperature Distribution) International conference
Yoya NAGANO, , Keishi TANAKA, Yu SAIKI, Yojiro ISHINO
Event date： 2010.12
Language：Japanese Presentation type：Oral presentation (general)
-
ギネス世界記録認定158眼カメラによる乱流火炎計測
石野 洋二郎，齋木 悠，富田 和史，珠久 陽輔，大北 雄哉，堀本 健太，徐 ヨウ
名工大名市大合同テクノフェア 名古屋工業大学
Event date： 2010.11
Language：Japanese Presentation type：Poster presentation
Venue：吹上ホール
自立型等身大ヒューマノイドロボットの跳躍動作の実現に対し，①自立性：電池ではなくカセットボンベを使用，②等身大大型物駆動：燃焼エネルギーを利用，③跳躍動作：二関節筋モデルを採用し，それぞれ工夫・対応を行っている．とくに，燃焼アクチュエータでは，燃焼の駆動力をバネの力学エネルギーとして蓄積する方式を採用した．
-
燃焼とその応用・非応用機器開発（ギネス世界記録認定158眼カメラによる乱流燃焼計測から人間搭乗型ロボットまで）
石野 洋二郎
名工大名市大合同テクノフェア 名古屋工業大学
Event date： 2010.11
Language：Japanese Presentation type：Oral presentation (invited, special)
Venue：吹上ホール
燃焼技術とその応用・非応用機器開発について発表講演を行った．具体的には，ギネス世界記録認定された燃焼三次元計測用の158眼カメラによる乱流燃焼計測，ならびに，燃焼を駆動力として跳躍する等身大ヒューマノイドロボットの開発，人間搭乗型ロボットの開発，などについて，報告を行った．
-
等身大跳躍ロボットと燃焼式直動アクチュエータの開発
石野 洋二郎，齋木 悠，大澤 明日菜，岩澤 宏太
名工大名市大合同テクノフェア 名古屋工業大学
Event date： 2010.11
Language：Japanese Presentation type：Oral presentation (general)
Venue：吹上ホール
等身大ヒューマノイドロボットの跳躍駆動を実現するために，燃焼式直動アクチュエータを開発し，製作した等身大ヒューマノイドロボットへ搭載し，ロボットの跳躍挙動を高速度カメラ撮影などのより分析した．その結果，数ｃｍの跳躍が確認でき，実験は成功裏に遂行された．
-
搭乗可能型の二脚式無動力移動ロボットの開発＜試乗可＞（ロボ・アスリート・プロジェクト）
石野 洋二郎，齋木 悠，大澤 明日菜，岩澤 宏太
名工大名市大合同テクノフェア 名古屋工業大学
Event date： 2010.11
Language：Japanese Presentation type：Poster presentation
Venue：吹上ホール
移動方法の多様性を広げるため，二足歩行に関する新しい歩容生成方法を考案した．この歩行方法は，完全静歩行であり，安定な歩行が無動力で達成できる．このため，人間が搭乗しても安全な，搭乗型歩行ロボットを製作し，アミューズメント分野への展開を促進する．全長２．５ｍの搭乗ロボット実機での試乗体験会も行い，テレビ取材を受けた．
-
急速加熱された単一PET 樹脂粒子の多相燃焼過程に及ぼす周囲ガス流速の影響
深澤 俊晴, 納谷 裕輔, 藤田 菜保, 齋木 悠, 石野 洋二郎, 大岩 紀生
熱工学コンファレンス 日本機械学会
Event date： 2010.10
Language：Japanese Presentation type：Oral presentation (general)
Venue：長岡市
急速加熱された単一PET 樹脂粒子の多相燃焼過程に及ぼす周囲ガス流速の影響について，顕微鏡下での高速度ビデオ観察を行い，廃棄プラスチック粉末のサーマルリサイクルに関する重要な基礎データを得た．
-
二次元燃焼流の密度境界におけるバロクリニックトルクおよび浮力渦度の生成機構
稲葉 耕作, 片岡 誠仁, 齋木 悠, 石野 洋二郎
熱工学コンファレンス 日本機械学会
Event date： 2010.10
Language：Japanese Presentation type：Oral presentation (general)
Venue：長岡市
二次元燃焼流の密度境界におけるバロクリニックトルクおよび浮力渦度の生成機構について，浮力対応型離散渦法による数値解析，ならびに，可視化実験により調査した．
-
Study on a Full-Scale Jumping Humanoid Robot and Jumping Equipment Driven by a Novel Combustion Linear Actuator
Asuna OSAWA, Ryohei SHIBATA, Akira TORII, Nobuyuki ITOU, Rie OGAWA, Shouta TAMAKOSHI, Yutaka NANBU, Yu SAIKI, Yojiro ISHINO
Event date： 2010.09
Language：Japanese Presentation type：Oral presentation (general)
-
廃ガスを集中管理可能なリジェネ高効率ガスコンロの試作と作動特性
伊藤 正佳，澤村 智也，樋口 洋介，齋木 悠，石野 洋二郎，大岩 紀生
第20回環境工学シンポジウム2010 日本機械学会
Event date： 2010.06
Language：Japanese Presentation type：Oral presentation (general)
Venue：パシフィコ横浜
廃ガスを集中管理可能なリジェネ高効率ガスコンロの試作を行い，作動特性について調査した．とくに，廃ガスの熱量（排熱）を熱交換器により新気に熱交換する「リジェネ」の効果について各種燃焼条件にて燃焼データを収集した．
-
MEASUREMENT OF A LOCAL BURNING VELOCITY OF A TURBULENT PREMIXED FLAME BY SIMULTANEOUS 3D-CT RECONSTRUCTION WITH 40-LENS CAMERA AND STEREOSCOPIC PTV International conference
Y. Saiki, Y. Tomida, S. Shiga, Y. Ishino, N. Ohiwa
第８回工学的乱流モデリングと計測に関する国際会議
Event date： 2010.06
Language：English Presentation type：Oral presentation (general)
Venue：マルセイユ，フランス
Non-scanning 3D computerized tomography (3D-CT) technique (Ishino and Ohiwa(2005), Ishino et al.(2007)) have been proposed and accomplished for the propane/air fuel-rich premixed flames. More-over in this paper, an instantaneous local burning ve-locity of the turbulent premixed flame is evaluated from two 3D-CT volume data of light emission in-tensity with short time-interval of 1.29 ms and a 3D particle track simultaneously taken by stereoscopic PTV(Particle Track Velocimetry).
-
Time-Resolved Multi-Dimensional Temperature Measurement of a Turbulent Flame with Heat Radiation from a Hi-Nicalon Fiber Array
Yosuke HIGUCHI, Takahiro IMAEDA, Yoya NAGANO, Yu SAIKI, Yojiro ISHINO, Norio OHIWA
Time-Resolved Multi-Dimensional Temperature Measurement of a Turbulent Flame with Heat Radiation from a Hi-Nicalon Fiber Array
Event date： 2010.05
Language：Japanese Presentation type：Oral presentation (general)
-
世界で最もレンズの多いカメラ（158眼カメラ：ギネス世界記録）と四次元ＣＴ（コンピュータ断層映像）燃焼計測
石野 洋二郎
電気学会東海支部総会 電気学会
Event date： 2010.04
Language：Japanese Presentation type：Oral presentation (invited, special)
Venue：名古屋ガーデンパレスホテル
乱流燃焼の瞬間三次元ＣＴ（コンピューター断層）計測用に設計・製作した「１５８眼カメラ」について，その構造，ならびに時系列四次元ＣＴ計測例を報告した．また，同カメラは，「世界で最もレンズの多いカメラ」としてギネス世界記録認定されているので，その申請から認定までの経緯についても報告を行った．
-
Measurement of Instantaneous 3D-Distribution of Local Burning Velocity on a Turbulent Premixed Flame by Non-Scanning 3D-CT Reconstruction International conference
Fourth European Combustion Meeting 2009
Event date： 2009.04
Language：Japanese Presentation type：Poster presentation
-
High-Speed Microscopic Observation and Modeling of the Multi-Phase Process in a Micro Spherical PET Particle under Abrupt Heating International conference
Sixth Mediterranean Combustion Symposium,
Event date： 2009.04
Language：Japanese Presentation type：Oral presentation (general)
-
Enhancement behavior of Combustion and Heat Transfer in Four Types of Constant-Volume Combustors International conference
7th World Conference on Experimental Heat Transfer, Fluid Mechanics and Thermodynamics
Event date： 2009.04
Language：Japanese Presentation type：Oral presentation (general)
-
High-Speed Imaging of Transition Process of Flame Patterns around Micro PET Particles Flying Through Oscillating Combustion Gas Flow International conference
The 7th Pacific Symposium on Flow Visualization and Image Processing
Event date： 2009.04
Language：Japanese Presentation type：Oral presentation (general)
-
Analysis of Vorticity Formation Process in a Density Boundary Layer of Burnt Gas Flow by Discrete Vortex Simulation International conference
International Workshop on Environment & Engineering Advanced Sustainable Cities
Event date： 2009.04
Language：Japanese Presentation type：Poster presentation
-
Experimental Investigation of Vorticity Formation Process in a Density Boundary Layer of Burnt Gas Flow International conference
International Workshop on Environment & Engineering Advanced Sustainable Cities
Event date： 2009.04
Language：Japanese Presentation type：Poster presentation
PREV - NEXT 